skip to Main Content
Blebricks

The Blebricks family consists of various sensor models, such as the environmental, touch, orientation, and presence detection’s ones, communication and power modules, infrared receivers, and mounting bases.

The users shall handle the included devices with care, avoiding to create short-circuits, bend connectors, apply inadequate forces on the devices and particularly on the electronic components, expose the devices to water and temperatures lower than 0°C and higher than 45°C, or create any other possible damaging scenario.

In order to disassemble stacked Blebricks, it is recommended to use a dielectric object as a lever and apply a uniform and weak force in order to not bend connectors.

Il Blebrick RPS è Un Modulo Di Alimentazione Che Include Un Caricatore Per Batterie Li-Po / Li-Ion Micro-USB (Type B)
Il Blebrick RPS è Un Modulo Di Alimentazione Che Include Un Caricatore Per Batterie Li-Po / Li-Ion Micro-USB (Type B)
RPS
Il Blebrick RPS è Un Modulo Di Alimentazione Che Include Un Caricatore Per Batterie Li-Po / Li-Ion Micro-USB (Type B)
RPS
Il Blebrick RPS è Un Modulo Di Alimentazione Che Include Un Caricatore Per Batterie Li-Po / Li-Ion Micro-USB (Type B)
RPS

The RPS Blebrick is a single-position mounting base brick including a Li-Po / Li-Ion micro-USB (Type B) battery charger.

It is possible to use it to supply power to other Blebricks either using a Li-Po / Li-Ion battery or using a 5 VDC power supply connected through the micro-USB (Type B) port.

Such brick is also able to properly charge Li-Po / Li-Ion batteries.

Dimensions (naked): 22.5 mm x 22.5 mm
Dimensions (packaged): 27 mm x 27 mm

Output voltage: 3.0 V
Maximum input voltage (USB): 5.0 V

When only the battery is plugged in, the LED is turned off.
When only the micro-USB 5VDC power source is plugged in, the green LED is turned on.
When both the battery and the micro-USB 5VDC power source are connected, the green LED is always on, while the red LED is on only during battery charging.

Dimensions: 12 mm x 22 mm x 6 mm

Capacity: 80 mAh
Maximum continuous discharge current: 80 mA
Temperature ranges: 0 to +45°C (charge); -20°C to +60°C (discharge)
Humidity range: 65% ±20% r.H.

Il Blebrick SPS è Un Modulo Di Alimentazione Che Include Un Supporto Per Una Batteria A Bottone (CR1632)
Il Blebrick SPS è Un Modulo Di Alimentazione Che Include Un Supporto Per Una Batteria A Bottone (CR1632)
SPS

The SPS Blebrick is a single-position mounting base brick including a coin cell (CR1632) battery holder.

It is possible to use it to supply power to other Blebricks. However it is recommended to use it only for low power applications since the battery cannot be recharged and will have to be replaced when empty.

Dimensions (naked): 22.5 mm x 22.5 mm
Dimensions (packaged): 27 mm x 27 mm

Output voltage: 3.0 V

Dimensions: 16 mm x 3.2 mm

Capacity: 120 mAh
Temperature range: -30 °C to +70 °C

Please be sure to place the battery in the correct position, i.e. the upper side shall be the positive side.

Please note that if you are using the BLE-B with a fast advertising interval (i.e. < 1 s), or with any observing interval it is recommended to take in account a different kind of power supply.

Batteria
Batteria
XPS

The XPS Blebrick supports AA batteries with any chemistry (alkaline, lithium-thionyl chloride etc.) and any additional source from 0,8 Vdc to 6 Vdc.
It also support solar cell panels up to 6V, that can be used together with a rechargeable 3,6 V back-up battery.

Additionally, the XPS is sold to function as a battery; if you want to use it with solar panel, you need to specify it before ordering.

The XPS Blebricks features two operating modes:
1) Power supply mode with battery or any external source (from 0,8 V dc to 6 V dc) connected to Blebricks
2) Battery charger mode when the external source (such as solar panel) is used to charge a back-up rechargeable battery.

Dimensions (Expert): 90 mm x 20 mm

Supply voltage: 0,85 V – 6 V
Output voltage: 3 V
Max current consumption: 300 mA
Operating temperature range: – 40 + 125°C

The device operates by default in power supply mode. In order to activate external sources input (e.g. solar panels), the R16, R17, R18 and R19 jumpers shall be opened, and R4, R5 and R7 shall be activated.

Please note that this Blebricks is only available in expert (naked) version.

Batteria
Batteria
BPS

The Blebrick BPS is a power supply module suitable for industrial applications that supports input voltages between 3.6 V and 24 V, via terminal block connector.

It is possible to use it to supply power to other Blebricks.

Dimensions (naked): 22.5 mm x 22.5 mm
Dimensions (packaged): 27 mm x 27 mm

Output voltage: 3.0 V

Please note that this Blebrick is only available in the Expert version.

Back To Top